Engineering Specification · Prototype Build Package
KOOE kids' audio player · MD-1
Everything a hardware team needs to quote, design and build the first working prototypes: requirements, architecture, circuits, pin map, PCB rules, enclosure, bill of materials, assembly, firmware, bring-up and test plan.
| Document | MD-ENG-001 | Revision | 7.1 (design rev. 7.1) |
|---|---|---|---|
| Status | Released for prototype quotation (EVT) | Date | 2026-11-21 |
| Product | MD-1, 96 × 36 × 15 mm | Classification | Confidential · share under NDA |
| Owner | Product lead (Music Device) | Companion | Interactive UI simulator |
1Scope and deliverables
1.1 Purpose
MD-1 is a screen-light audio player for children aged 8–14. It plays music, podcasts and audiobooks offline from internal storage through wired headphones. Parents choose the content in a phone app; the device syncs over home Wi-Fi only while it is charging. It has no speaker, no microphone, no camera, no Bluetooth, no browser and no touch screen.
This document specifies the design at revision 7, which applies the decisions taken after an independent technical audit (docs/auditoria-tecnica-md1-rev6.md and docs/respuesta-auditoria-rev6.md), so that an engineering partner can produce the schematic, PCB, enclosure CAD and firmware, and build prototype units.
1.2 What is provided with this package
- This specification (requirements, architecture, pin map, layout rules, mechanical placement, BOM, procedures).
- The interactive UI simulator: every screen and key behaviour the firmware must reproduce (index.html).
- Component placement in millimetres (section 6.3), exploded view and automatic clearance check.
- Industrial design renders (repository
renders/; note they show an earlier 106 mm body, this document governs).
1.3 What the builder delivers
| # | Deliverable | Format | Phase |
|---|---|---|---|
| D1 | Schematic, reviewed against this document | PDF + native (KiCad preferred) | B |
| D2 | PCB layout, fabrication and assembly files | Gerber X2, drill, IPC-356 netlist, pick-and-place, assembly drawing | B, C |
| D3 | Costed BOM with manufacturer part numbers and one alternate per active part | XLSX/CSV | B, C |
| D4 | Enclosure, keypad and glass CAD; 2D drawings with tolerances | STEP + PDF drawings | C |
| D5 | Firmware source and build instructions | Git repository, ESP-IDF project | A, B, C |
| D6 | Assembled units: 3 works-like boards (phase B), 10 form-factor units (phase C) | Hardware | B, C |
| D7 | Bring-up and test report with measured values against section 12 | B, C |
2Product requirements
Every requirement has an ID and a way to check it. Section 12 references these IDs.
| ID | Requirement | Verification |
|---|---|---|
| Physical | ||
| R-01 | Outside size shall be 96.0 × 36.0 × 15.0 mm (±0.2), corner radius 7 mm in plan. | Caliper |
| R-02 | Mass should be ≤ 50 g without headphones (estimate 48 g with the front plate). | Scale |
| R-03 | No visible fasteners on the front face. Four screws from the back. | Inspection |
| User interface | ||
| R-10 | Display 1.9″ IPS, 170 × 320, landscape, under a recessed cover (glass or PC, 1.2 mm below the front plate surface). The front face follows the grid in section 6.4. | Inspection |
| R-11 | Front keys: previous, play/pause, next in a one-piece silicone keypad. Top edge: home/power, volume −, volume +. Bottom edge: HOLD slide switch. | Inspection |
| R-12 | Key behaviour and every screen shall match the UI simulator (holds, long press, sleep, HUD overlays). | Side-by-side review |
| R-13 | Front keys: actuation force 125–150 g, snap ratio 40–60 %, return force ≥ 30 g, switches rated ≥ 500,000 cycles. | Force gauge, datasheet |
| R-14 | The front plate shall come off and go back on by hand, without tools. Pull-off force 4–8 N at the notch. No magnet shall be accessible or come loose after use-and-abuse tests. ≥ 1,000 removal cycles without loss of hold. | Force gauge, abuse tests, cycle test |
| Audio | ||
| R-20 | 3.5 mm stereo headphone output only. No speaker, no Bluetooth. | Inspection |
| R-21 | The output network shall cap the voltage at the jack at ≤ 150 mV RMS (EN 50332-2 test signal) with every DAC register at its maximum, on any load from 16 Ω to open circuit. Kid mode default ≤ 27 mV. 16 volume steps. A dB(A) figure is promised only for the included headphones. | Audio analyser |
| R-22 | No audible pop or click at power on/off, sleep/wake, or plugging headphones. | Listening + scope on 32 Ω load |
| R-23 | Noise floor at the jack with digital silence should be ≤ 20 µV A-weighted. THD+N ≤ 0.1 % at 100 mV into 32 Ω, 20 Hz–20 kHz. | Audio analyser |
| R-24 | Playback pauses within 100 ms when headphones are removed. | Scope + firmware log |
| Power | ||
| R-30 | Battery LiPo 603040, 800 mAh, with protection circuit and 10 kΩ NTC. | Datasheet |
| R-31 | Objective: playback ≥ 16 h with the screen asleep, 128 kbps MP3, 27 mV output, new cell, 25 °C, cut-off 3.4 V under load. Needs ≤ 42.5 mA average. Promised only after a rundown on real units. | Rundown test |
| R-32 | Charge 0→100 % in ≈ 2.1 h without sync and ≈ 2.5 h while syncing, from a 5 V source able to supply 500 mA. No charge current outside 0–45 °C cell temperature, enforced in hardware. | Charge log, thermal chamber |
| R-33 | Deep-sleep current ≤ 100 µA. Ship mode ≤ 10 µA maximum, including the cell protection circuit. | µA meter |
| Connectivity and data | ||
| R-40 | Wi-Fi 2.4 GHz turns on only while USB power is present. The radio shall be off during battery playback. | Firmware log, RF sniffer |
| R-41 | 16 GB eMMC storage. USB shall expose no mass storage to the user in production firmware. | Inspection |
| R-42 | No microphone, camera or location hardware. | Schematic review |
| Robustness | ||
| R-50 | Survive 4 drops from 0.92 m onto vinyl tile over concrete, random orientation, still working, no sharp edges or loose parts (ASTM F963-23 use and abuse). | Drop test |
| R-51 | ESD ±8 kV contact / ±15 kV air on every touchable point, no damage, self-recovery (IEC 61000-4-2 level 4). | ESD gun |
| R-52 | Designed for IPX4 splashes (IEC 60529). No IP claim before a lab test. | Splash test |
| R-53 | USB-C 10,000 mating cycles; headphone jack ≥ 10,000 cycles. | Datasheet + cycle test |
3System architecture
3.1 Operating modes
| Mode | Entered by | What is on | Target current |
|---|---|---|---|
| Playing, screen asleep | 8 s without a key press | CPU 80 MHz, I²S, DAC/amp, eMMC bursts | 30–45 mA |
| Playing, screen on | Any key | + display, backlight 40 % | 45–60 mA |
| Paused | Play key | Light sleep, display off after 8 s | < 3 mA |
| Deep sleep | 5 min paused, or long-press home | RTC only, wake on home key / USB | < 100 µA |
| Charging + sync | USB power present | Charger, Wi-Fi in bursts, screen shows status | from USB |
| Ship mode | Factory command over USB | Battery disconnected by the charger, gauge asleep | ≤ 10 µA max |
4Electrical design
4.1 Power tree
| Rail | Source | Suggested part | Voltage | Max load | Loads |
|---|---|---|---|---|---|
| VBUS | USB-C | Low-voltage TVS for ESD + external OVP switch rated ≥ 28 V (builder's MPN) | 5 V | 475 mA typ. (500 mA setting) | Charger input |
| VSYS | BQ25180 power path | — | 3.4–4.4 V | 1 A | All regulators |
| VBAT | Cell via charger | Cell PCM + BQ25180 BATFET | 3.0–4.2 V | 1 A peak | VSYS when unplugged |
| 3V3 | VSYS | TI TPS63802 buck-boost (works across the whole battery range) | 3.3 V | 600 mA peaks (Wi-Fi TX) | ESP32-S3, eMMC, display, keys, IOVDD |
| 3V0_A | VSYS | Low-noise LDO, TI TPS7A2030 class (PSRR ≥ 60 dB at 1 kHz) | 3.0 V | 100 mA | DAC AVDD, HPVDD only |
| 1V8_D | 3V3 | TI TLV75518 class | 1.8 V | 50 mA | DAC DVDD (check datasheet) |
| VLED | 3V3 via N-MOSFET | PWM 20 kHz from GPIO7 | — | ~30 mA | Display backlight |
The audio LDO enable (GPIO21) lets firmware switch the analog rail off in deep sleep and sequence it for pop-free start-up. The 3V0_A rail keeps working down to about 3.15 V battery; below that the gauge triggers a controlled shutdown anyway (cut-off 3.4 V under load).
4.2 Processor and pin map
EVT shall use the pre-certified module ESP32-S3-MINI-1U-N4R2: 4 MB quad flash, 2 MB quad PSRAM in package, 15.4 × 15.4 × 2.4 mm (Espressif datasheet v1.7, table 1-1). Its RF connector is the third-generation type compatible with Hirose W.FL, I-PEX MHF III and Amphenol AMC, not U.FL. The module removes RF layout, and the product can build on Espressif's grant only within its conditions: an external antenna of the same type with gain ≤ 2.33 dBi (§10.2), labelling, and the product's own Part 15 B and RF-exposure assessment. Memory budget to confirm in phase A: 108.8 KB per full display frame, the decoder, the TLS/Wi-Fi stack, two OTA slots and a factory slot in 4 MB. Chip-down is a later cost step, not a prototype task.
| GPIO | Signal | Dir | Notes |
|---|---|---|---|
| 0 | BOOT | in | Strapping pin. Test pad only, 10 k pull-up. Do not use. |
| 1 / 2 | I2C_SDA / I2C_SCL | i/o | 2.2 k pull-ups to 3V3. Devices: BQ25180, MAX17048 (0x36), TLV320DAC3100 (0x18), cell temperature sensor. Confirm addresses. |
| 3 | — | — | Strapping pin, leave unused. |
| 4 / 5 / 6 | I2S_BCLK / I2S_WS / I2S_DOUT | out | To DAC. 22 Ω series resistors at the source. DAC PLL runs from BCLK (no MCLK). |
| 7 | LCD_BL_PWM | out | Gate of backlight MOSFET, 100 k pull-down. |
| 8 / 9 / 10 | LCD_RST / LCD_DC / LCD_CS | out | |
| 11 / 12 | LCD_MOSI / LCD_SCLK | out | SPI2, 40 MHz. Keep under 30 mm, over solid ground. |
| 13 | KEY_HOME | in | RTC GPIO, wakes from deep sleep (ext0). Not connected to the charger's TS/MR pin (decision D-6). |
| 14 | LED_CHG | out | 0603 LED, 1 kΩ, under the light pipe. |
| 15 | KEY_PLAY | in | RTC GPIO (also usable as wake). |
| 16 | GAUGE_ALRT | in | Open drain, 100 k pull-up. Low battery and 1 % change alerts. |
| 17 | HOLD_SW | in | RTC GPIO. Low = locked. |
| 18 | CHG_INT | in | BQ25180 /INT: plug-in, fault, temperature. |
| 19 / 20 | USB_D− / USB_D+ | i/o | Native USB: firmware flashing, logs, factory commands. 90 Ω differential. |
| 21 | AUDIO_EN | out | Enable for 3V0_A and 1V8_D LDOs, 100 k pull-down. |
| 38 / 39 / 40 | EMMC_CLK / EMMC_CMD / EMMC_D0 | i/o | SDMMC host, 1-bit at 40 MHz (≈ 5 MB/s, well above audio + Wi-Fi rates). 10 k pull-ups on CMD and D0–D3. Route D1–D3 to pads for a later 4-bit mode. |
| 41 / 42 | KEY_PREV / KEY_NEXT | in | Internal pull-ups, firmware debounce 15 ms. |
| 47 / 48 | KEY_VOL_DN / KEY_VOL_UP | in | Internal pull-ups. |
| 45 / 46 | — | — | Strapping pins, leave unused. |
| EN | RESET | in | RC 10 k / 1 µF, test pad. |
The builder shall check this map against the exact module datasheet: which GPIOs are bonded out, and which are taken by the module's flash and PSRAM. If a pin is unavailable, move it and update this table. Checked against ESP32-S3-MINI-1U v1.7: GPIO26 is taken by the PSRAM on N4R2 and is not used here; GPIO38–42, 47 and 48 are bonded out; GPIO39–42 default to JTAG and are free when debugging over USB-JTAG.
4.3 Circuit blocks
USB-C (sink only)
- 16-pin USB 2.0 receptacle, mid-mount, splash-proof (IPX4) type, through-hole shell legs.
- CC1 and CC2: separate 5.1 kΩ Rd to ground each. Never share one resistor.
- VBUS: low-voltage TVS (ESD) + external OVP switch rated ≥ 28 V in front of the charger + 10 µF (D-5). The charger's own OVP (5.7 V typ.) does not cover spikes above its 25 V absolute maximum. CC and D±: low-capacitance ESD array (≤ 1 pF) right at the connector.
- Shell to ground through 1 MΩ ∥ 4.7 nF.
Charger: BQ25180
- Charge current 400 mA (0.5 C), termination 10 %, regulation 4.20 V, input limit setting 500 mA (475 mA typ.). System load has priority over charging.
- 45 °C trip in hardware (D-4). The BQ25180 defaults to HOT = 60 °C, and its I²C watchdog (on by default, 160 s) restores defaults if the MCU stops talking. So the NTC network (series/parallel resistors per TI SLUAAJ8, with the cell's real B-curve) is sized so the charger's default HOT threshold is reached at 45 °C cell temperature. Registers can then only make it stricter.
- Ship mode set by the factory test station, gauge put to sleep first; wakes on USB plug-in. TS/MR carries only the NTC: the home key is not connected (D-6), so the default 10 s long-press-to-ship action cannot trigger.
- Firmware writes and reads back every register at boot and after any CHG_INT. On an I²C failure it shows "charging paused" and relies on the hardware trip.
Fuel gauge: MAX17048
- ModelGauge, no sense resistor. Needs the cell's model data from the supplier.
- The host must update RCOMP from the battery temperature at least once a minute (MAX17048 datasheet). The charger gives no temperature number, so an I²C temperature sensor sits against the cell.
- Alert at 10 %. Shutdown at 3.4 V under load or 3 % state of charge, whichever comes first (save playback position first). Sleep mode (0.5–2 µA) before ship mode.
Display
- 1.9″ IPS 170 × 320, ST7789, 4-wire SPI, FPC to a 0.5 mm-pitch ZIF connector near the right of the display footprint.
- Backlight: N-MOSFET low-side, PWM 20 kHz, default 40 %.
- Partial redraws only (progress bar, clock) to save power.
- Panel MPN still open: it sets backlight LED current (resistor or current driver), FPC exit side and whether the active area is centred in the module.
Storage: eMMC 16 GB
- eMMC 5.1, 11.5 × 13 mm FBGA-153, VCC and VCCQ at 3.3 V, 100 nF + 4.7 µF on each.
- RST_n to 3V3 through 10 k. 0.65 mm-pitch BGA may need via-in-pad: confirm with the PCB house.
Audio: TLV320DAC3100
- I²S slave, 44.1/48 kHz, 16-bit. Clock from BCLK through the internal PLL.
- Headphone driver only; class-D speaker output not used (leave per datasheet).
- Headphone detect through the jack's switch pin to the DAC's detect input.
- Output is AC-coupled (the DAC has no capless mode): two DC-blocking capacitors, ≈ 100–220 µF (100 µF on 32 Ω ≈ 50 Hz corner). Common mode 1.5 V (≤ AVDD/2 at HPVDD 3.0 V).
- Hardware level cap (D-3): a series resistor to the jack and a shunt resistor to ground at the jack, starting at 47 Ω / 7.5 Ω (TBD-EVT). With the amplifier at its supply-limited swing (≈ 1.06 V RMS, estimate), the jack sees ≈ 146 mV open, 121 mV on 32 Ω and 104 mV on 16 Ω, whatever the firmware writes. Driver gain locked at 0 dB and read back after every reset.
- Separate analog ground area under the DAC, joined to the main ground at one point near the jack.
Keys, HOLD, LED
- 6 × 6 mm front tact switches at 1.0 N (≈ 130 g at the keycap with the silicone), right-angle tact switches on the top edge, all ≥ 500k cycles.
- Active low, internal pull-ups. No external debounce parts.
- HOLD slide switch: when locked, firmware ignores every key and the home key cannot wake the device.
Antenna
- 2.4 GHz FPC antenna, about 14 × 4 mm, gain ≤ 2.33 dBi (the module grant's limit), on the inside of the top wall at x 9.2–23.2 mm.
- ≥ 4.2 mm from the screw boss and the home switch, ≥ 3 mm from the display, ≥ 20 mm from the cell.
- Pi-match pads (0402) on the feed for tuning in EVT.
4.4 Protection summary
| Entry point | Threat | Protection |
|---|---|---|
| USB-C VBUS | ESD, hot-plug surge, wrong 9–20 V adapter | Low-voltage TVS + external OVP switch ≥ 28 V (charger IN absolute max 25 V) |
| USB-C CC, D± | ESD ±8 kV contact | Low-capacitance TVS array at the connector, short ground |
| Headphone jack L, R, detect | ESD from the plug and cable | Bidirectional TVS per line, then series resistor |
| Keys, HOLD | Air discharge through gaps | No air path: silicone keypad and silicone boots (no TVS needed) |
| Cell | Over-charge, over-discharge, short | Cell PCM + charger with 45 °C hardware trip + firmware cut-off at 3.4 V / 3 % |
5PCB design rules
| Outline | 91 × 30 mm, 1.0 mm FR-4 (Tg ≥ 150), notch 11 × 8 mm at the left end around the mid-mount jack (section 6.3). Corner radius ≥ 1 mm. |
|---|---|
| Stack-up | 4 layers: L1 components + signals · L2 solid ground · L3 power (3V3, VSYS, 3V0_A islands) · L4 components + signals. Impedance-controlled for USB D± (90 Ω diff). |
| Sides | Front (toward the display): key switches, display connector, charger, LED. Back (toward the battery): module, eMMC, DAC, regulators. No parts at all under the battery footprint (x 47–87, y 3–33): a 0.3 mm insulating film sits between board and cell. Module, eMMC and regulators sit behind the screen. |
| Min. features | 0.1 mm track/space, 0.2 mm drill. Via-in-pad only if the eMMC BGA needs it. |
| ESD | TVS within 3 mm of each connector pin, ground via next to each TVS ground pad, no stub between connector and TVS. |
| Audio | DAC within 15 mm of the jack. L/R traces guarded by ground, away from SPI, I²S clock and the buck-boost inductor. |
| Power | Buck-boost loop as small as possible, inductor on the opposite side from the DAC. Bulk 22 µF at the module's 3V3 pin. |
| RF | No copper on any layer under the W.FL / MHF III pigtail route near the antenna, per the module guide. |
| Test points | Ø1.0 mm pads on the back: VBUS, VSYS, VBAT, 3V3, 3V0_A, 1V8_D, GND ×3, EN, BOOT, USB D±, I2C SDA/SCL, I2S BCLK, HP_L, HP_R. Jumper J-AUDIO forces AUDIO_EN high for bring-up. Placed for a pogo-pin fixture. |
| Fixing | Four open U-slots, 2.2 mm wide, where the screws pass (x 3.0 / 93.0, y 4.8 / 31.2). The board edge is at x 2.5, so a closed hole cannot fit. The board is located by two pins and clamped between front-shell bosses and back-shell ribs. 1.5 mm copper keep-out around each slot. |
| Markings | Board name, revision, date code, polarity on the battery connector. |
6Mechanical design
6.1 Coordinate system
All positions are in millimetres. Origin at the top-left corner of the front face, seen from the front. x runs right along the length (0–96), y runs down along the height (0–36), z runs from the front face (0) to the back (15).
6.2 Enclosure
| Construction | Two shells: front shell (front face and the full side walls' front 1.5 mm) and back shell (floor and side walls). Tongue-and-groove seam with a TPE gasket in the groove. |
|---|---|
| Material | Production: PC/ABS, moulded-in colour (e.g. Covestro Bayblend class), UL94 HB minimum. Prototype: see section 8. |
| Walls | Front 1.5 mm · side walls 1.4 mm · back floor 1.35 mm. Variation ≤ 15 %. |
| Draft | ≥ 0.5° on internal walls and bosses; ≥ 1° plus 1° per 0.025 mm of texture depth on textured outside faces. |
| Ribs | 0.7–0.8 mm thick (50–60 % of wall), ≤ 4 mm tall, to locate the battery and stiffen the floor. |
| Bosses | Four, in the front shell, at (3.0, 4.8), (93.0, 4.8), (3.0, 31.2), (93.0, 31.2). Outside Ø4.0 behind the display (z ≥ 2.6), stepping to a Ø2.8 neck beside it (z 1.5–2.6), pilot hole Ø1.3 for M1.6 thread-forming screws, tied into the end walls with ribs, base radius 0.3 mm. |
| Fasteners | 4 × M1.6 × 12 thread-forming screws for plastic, pan head, from the back. Tightening torque starts at 0.10 N·m, TBD-EVT (stay below 60 % of the strip torque). |
| Cover window | Two candidates built and tested in EVT (D-7): (a) 0.7 mm chemically strengthened aluminosilicate with anti-splinter PET film; (b) 0.8 mm polycarbonate with hard-coat. Both 51.9 × 29 mm with a black print border, bonded to a 1 mm adhesive ledge behind the 49.9 × 27 mm opening, front surface 0.4 mm below the front-shell face and 1.2 mm below the plate surface. Pocket depth 1.0 mm: glass + 0.3 mm tape or PC + 0.2 mm tape. |
| Keypad | One-piece silicone, 50–60 Shore A, two-shot colour (play key in the accent colour), conductive-free (presses the tact switch domes). Sealing lip clamped between front shell and board. |
| Top keys, HOLD | Silicone boots inside the shell; no open holes into the interior. |
| Openings | USB-C 9.4 × 3.8 mm with 0.3 mm chamfer, receptacle face 0–0.2 mm behind the outside surface. Jack Ø6.2 mm, jack nose flush ±0.1. LED: light pipe glued in a Ø1.6 hole. |
| Feet | Two TPE feet on the bottom edge. |
| Battery stack | z (mm): plate 0–0.8 → front shell → board back 5.7 → 0.3 mm insulating film → cell 6.0–12.2 (6.2 mm maximum, supplier to confirm) → 0.5 mm foam → 0.95 mm free swelling room (≈ 15 %) → floor at 13.65. If the supplier needs more than 15 %, the body grows to 15.8 mm rather than giving up the plate. Locating ribs on 3 sides, pull-tab stretch-release adhesive, nothing under or sharp against the pouch. The supplier's end-of-life swelling shall stay below the free room. |
| Display | 0.3–0.5 mm foam between display and board. |
6.3 Component placement
Generated from the same 3D model the clearance check runs on (0 collisions, 0 clearance warnings at this revision).
6.4 Front face layout
The front face uses two spacings only. M = 2.9 mm is the outer margin: from the plate edge to the screen window on the left, top and bottom, between the window and the key tray, and from the tray to the right edge. P = 1.3 mm is the inner gap of the tray: around and between every key. These values are design intent: tolerances shall not change them by more than ±0.1 mm, and any change to one element shall keep both rules.
| Element | x (mm) | y (mm) | Size (mm) | Rule |
|---|---|---|---|---|
| Body | 0 – 96 | 0 – 36 | 96 × 36, R 7 | — |
| Front plate (swappable, section 6.5) | 1.6 – 94.4 | 1.6 – 34.4 | 92.8 × 32.8, R 5.4 | 1.6 mm reveal all round |
| Screen window (glass opening) | 4.5 – 54.4 | 4.5 – 31.5 | 49.9 × 27.0, R 3.6 | M on left, top, bottom |
| Display active area | 8.1 – 50.8 | 6.65 – 29.35 | 42.7 × 22.7 | Centred in the window: 3.6 sides, 2.15 top and bottom |
| Key tray | 57.3 – 91.5 | 11.4 – 24.6 | 34.2 × 13.2, R 3.6 | M to window and to right edge; centred in height |
| Previous key | 58.6 – 66.6 | 12.7 – 23.3 | 8.0 × 10.6, R 2.6 | P to tray edges and to the next key |
| Play / pause key | 67.9 – 80.9 | 12.7 – 23.3 | 13.0 × 10.6, R 2.6 | P each side |
| Next key | 82.2 – 90.2 | 12.7 – 23.3 | 8.0 × 10.6, R 2.6 | P each side |
| Home key (top edge) | 22.95 – 35.95 | top edge | 13.0 wide | Centred on the screen window (x 29.45) |
| Volume − / + (top edge) | 67.9 – 80.9 | top edge | 13.0 wide in total | Centred on the play key (x 74.4) |
Check: 2.9 + 49.9 + 2.9 + 34.2 + 2.9 = 92.8 (plate width) and 1.3 + 8 + 1.3 + 13 + 1.3 + 8 + 1.3 = 34.2 (tray width). Switches sit centred under their keys (section 6.3). The display module moved 1.05 mm left to keep its active area centred in the window; the left screw bosses step to a Ø2.8 neck beside it (section 6.2).
6.5 Swappable magnetic front plate
The front plate is a separate 0.8 mm part that children can take off and put back without tools, so limited editions can be sold as plates instead of whole devices. The front shell stays the structural, sealed part: it holds the cover window, the keypad and the screws, so taking the plate off changes nothing about splash or drop protection.
| Plate | 92.8 × 32.8 × 0.8 mm, R 5.4, same outline as the old seam line. PC/ABS (or PC for clear or printed editions). Openings: screen window 49.9 × 27 and key tray 34.2 × 13.2, same grid as section 6.4. Nail notch 5 × 1.2 mm on the bottom edge, 6 mm from the right end. |
|---|---|
| Recess | 0.8 mm deep in the front shell, 0.15 mm clearance per side, edges radiused 0.3 mm so sand and dust do not jam it. The surface under the plate is finished and coloured: a device without its plate still looks intended. |
| Retention | Left: a 12 × 0.6 mm tongue on the plate hooks under a lip of the shell (slot at y 12–24). Right: four magnets in the shell pull four steel discs in the plate. To fit: hook the left edge, press the right side flat. To remove: lift at the notch; the plate hinges open from the hook. |
| Magnets (in the device) | 4 × NdFeB Ø3 × 1 mm, nickel-plated, at (66, 6.5), (86, 6.5), (66, 29.5), (86, 29.5). Insert-moulded or sealed in blind pockets from the inside, under ≥ 0.5 mm of front-shell plastic. ≥ 40 mm from the antenna, clear of the keypad and the switches (automatic check: 0 collisions). |
| Steel (in the plate) | 4 × stainless steel 430 (magnetic) discs Ø4 × 0.5 mm, heat-staked or glued in pockets on the back of the plate. The removable part never carries a magnet. |
| Hold force | Target 4–8 N to pull off at the notch (TBD-EVT). Strong enough not to fall off in a pocket; weak enough for a child. In a hard drop the plate may pop off instead of breaking: that is acceptable. |
| Safety | ASTM F963 treats a magnet as hazardous when its flux index is ≥ 50 kG²·mm² and it fits the small-parts cylinder; this applies to toys for children under 14. Small NdFeB discs like these are expected to be hazardous, so they shall stay inaccessible and must not come loose after use-and-abuse tests (drop, torque, tension). EN 71-1 has an equivalent rule. The lab confirms the classification (O-11). |
| Editions | One plate tool for every edition. Variety comes from colour, print (pad, UV or in-mould labelling) and metal finishes (vacuum metallising or metallic paint over plastic, never solid metal, which would detune the antenna and add weight). |
7Bill of materials
Costs are estimates at 10,000 units. The builder's costed BOM (D3) replaces them.
7.1 Suggested part numbers for EVT
| Function | Suggested | Alternate |
|---|---|---|
| MCU module | Espressif ESP32-S3-MINI-1U-N4R2 (4 MB flash, 2 MB PSRAM) | ESP32-S3-MINI-1U-N8 (8 MB flash, no PSRAM) if the memory budget allows |
| Charger | TI BQ25180 | TI BQ25155 (with ADC) |
| Fuel gauge | Analog Devices MAX17048 | TI BQ27220 |
| 3V3 regulator | TI TPS63802 | TI TPS63031 |
| Audio LDO | TI TPS7A2030 class | Any low-noise LDO with PSRR ≥ 60 dB at 1 kHz |
| Audio DAC + HP amp | TI TLV320DAC3100 (VQFN-32, 5 × 5 mm) | A stereo DAC with a ground-referenced (capless) headphone output, chosen with its datasheet. ES8311 is mono and is not an alternative. |
| eMMC | 16 GB eMMC 5.1, FBGA-153 (Kingston, Samsung, SanDisk or Longsys) | Same, 8 GB (cost) |
| Display | 1.9″ IPS 170 × 320, ST7789V3, SPI, FPC | Two sources with the same outline |
| Cell | LiPo 603040 800 mAh, PCM, 10 k NTC, 3 wires, UN38.3 and IEC 62133 reports, maximum thickness and end-of-life swelling in writing | 650 mAh same size |
| USB-C receptacle | 16-pin, mid-mount, IPX4 splash-proof (TE splash-proof Type-C family) | Hirose waterproof Type-C (gasket + potting) |
| Headphone jack | 3.5 mm 4-pole, mid-mount, with detect switch, ≥ 10k cycles | — |
| Front switches | 6 × 6 mm SMD tact, ≥ 500k cycles, 1.0 N | — |
| Top switches | Right-angle SMD tact, ≥ 500k cycles | — |
| ESD | Low-voltage VBUS TVS (ESD), low-capacitance array for CC/D±, TVS per audio line | Nexperia, Littelfuse equivalents |
| Input overvoltage | OVP load switch rated ≥ 28 V in front of the charger | Builder's MPN |
| Cell temperature | I²C digital temperature sensor against the cell (for gauge RCOMP and the UI) | Builder's MPN |
| Cover window | 0.7 mm strengthened glass + anti-splinter film | 0.8 mm PC with hard-coat (both in EVT) |
| Plate magnets | 4 × NdFeB Ø3 × 1 mm, nickel-plated, sealed in the front shell | Same size, N35–N42 grade chosen for the 4–8 N target |
| Plate steel | 4 × stainless steel 430 discs Ø4 × 0.5 mm | Plain steel, nickel-plated |
8Build plan, phase by phase
Do not jump straight to the final shape. Each phase removes one kind of risk before the next one costs more.
- Phase A · Proof on dev boards (1–2 weeks). ESP32-S3 DevKitC + display breakout + TLV320DAC3100 breakout + micro-SD in place of eMMC + LiPo + charger eval board. Goal: firmware plays audio, drives the UI from the simulator, measures current per mode. Exit: R-12, R-24 and a first current budget.
- Phase B · Works-like board (2–3 weeks). Same circuits as the final design on a larger board (about 100 × 60 mm, 4 layers), every test point exposed, jumpers on each rail to measure current, headers for the keys. 3 units. Exit: all rails, audio (R-21 to R-23), charging (R-32), sleep current (R-33), Wi-Fi sync.
- Phase C · Looks-like + works-like EVT (4–6 weeks). Final 91 × 30 mm board in the final enclosure. 10 units. Shells: SLA resin for the first fit check, then vacuum-cast PC/ABS-like urethane (or CNC PC/ABS) for drop and splash tests, because printed resin does not behave like moulded PC/ABS in a drop. Silicone keypad from a soft (aluminium) tool or cast silicone. Exit: every test in section 12 run once.
- Phase D · DVT (after EVT sign-off, not in this package). Steel tools, production processes, certification samples.
9Assembly procedure (phase C)
Work on an ESD mat with a wrist strap. Inspect each part before use. Record the unit serial number at step 1.
- Board. Check the assembled PCB visually and run the bare-board power test (section 11, steps 1–4) before it goes into any shell. Label with the serial number.
- Flash. Program the factory test firmware over USB. Run the self-test: rails, I²C devices found, eMMC size, display pattern.
- Front shell face-down on a soft fixture that supports the front lip, not the glass opening.
- Cover window. Clean with IPA. Apply the adhesive ring to the 1 mm ledge. Place the cover (glass: film side in; PC: hard-coat side out), press at 20 N for 10 s with a flat pad. Check it sits 0.4 mm (±0.1) below the lip.
- Display. Peel the protective film. Place it into its pocket face-down onto the glass, active area centred in the black print window (±0.2 mm). Fit the 0.3–0.5 mm foam pad on its back.
- Keypad and boots. Seat the silicone keypad on its locating pins, sealing lip fully in its groove. Fit the top-key boots and the HOLD boot.
- Antenna. Stick the FPC antenna to the inside of the top wall at x 9.2–23.2 mm. Route the pigtail along the wall, no sharp bends (minimum bend radius per the pigtail datasheet).
- Board. Plug the display FPC into the ZIF connector and close the latch. Lower the board onto the bosses, front switches facing the keypad, jack and USB-C into their openings. Connect the antenna W.FL / MHF III plug (press straight down until it clicks; a U.FL cable does not fit).
- Battery. Check the cell voltage (3.6–3.9 V as shipped). Place the 0.3 mm insulating film on the board, the cell between its ribs with the pull-tab adhesive, then the 0.5 mm foam pad on its back. Plug the battery connector. Do not bend the cell or press on it with tools.
- Gasket. Place the TPE gasket into the back-shell groove, without twists or stretching.
- Close. Lower the back shell straight on. Drive the four M1.6 screws in a cross pattern to the set torque with an electric screwdriver and clutch. Never re-drive a stripped boss.
- Feet and label. Fit the TPE feet. Apply the regulatory label.
- Front plate. Hook the plate's left tongue under the shell lip, press the right side until the magnets pull it flat. Check it sits flush (±0.1 mm) and lifts off at the notch.
- Final test. Run the end-of-line test (section 11, step 12). Put the unit into ship mode. Record results against the serial number.
10Firmware specification
| Toolchain | ESP-IDF 5.x (current stable), C. FreeRTOS tasks. Build reproducible from the repository with one command. |
|---|---|
| Partitions | Bootloader · two OTA app slots (rollback on failed boot) · NVS (settings, profiles, volume cap) · factory test app. Content lives on the eMMC, not in flash. |
| Storage | FAT32 on eMMC through the SDMMC driver. Content in folders per category (Music, Podcasts, Stories, Science) plus an A/B manifest (sequence number + CRC). Sync writes temporary files, validates hashes, then publishes a new manifest; the previous library stays valid until then. Never auto-format on a recoverable error: FAT has no power-loss protection of its own. |
| Audio | Decode MP3 and AAC (Opus optional for spoken content), 44.1/48 kHz to I²S. Decoder runs on one core at 80 MHz; the UI on the other. Gapless where the format allows. Resume position saved every 10 s and at shutdown. |
| Volume policy | 16 steps, about 2.5 dB each, top step = the active cap. Kid mode cap set from the parent app, stored in NVS. 85 dB(A) warning once per session if the parent raised the cap. The hardware limit in section 4.3 stays regardless. Driver gain register locked at 0 dB and read back after every reset. |
| UI | Exactly as the simulator: home tiles, lists, now-playing, volume overlay, HOLD, low battery, charging and sync notices. Screen off after 8 s; the first key press only wakes the screen. |
| Keys | 15 ms debounce. Long press 600 ms. Prev/next held = seek ×8. Home held 2 s = power off. HOLD = ignore every key, checked before anything else: a locked key does not even wake the screen. |
| Power | Dynamic frequency scaling 80/160 MHz. Do not count on light sleep while I²S runs: the I²S driver holds a power-management lock while a channel is enabled (ESP-IDF). Stop I²S when paused, then light sleep; deep sleep after 5 min paused. Charger registers written and read back at boot and on CHG_INT. Wi-Fi only when USB power is present (CHG_INT / VBUS status), in bursts. |
| Sync | On plug-in: connect to the stored home network, authenticate to the parent backend over TLS, download the content diff with resume, verify hashes, update the index, disconnect. Wi-Fi set-up from the parent app over USB or a short-lived local set-up mode. |
| Security, privacy | Production: secure boot v2 and flash encryption on. Flash encryption covers the module flash, not the eMMC: content protection is a separate decision. Secure boot changes JTAG and USB recovery options, so the factory flow is validated with final eFuses. Signed OTA images only. COPPA: data inventory, identifiers, retention and deletion. No microphone or camera in hardware. |
| Factory app | USB commands: read serial, run self-test, set charger registers, measure audio loop, enter ship mode. |
11Bring-up procedure
Run on every phase B and phase C board, in order. Stop at the first failed step and record it.
| # | Step | Expected |
|---|---|---|
| 1 | Visual inspection under magnification: polarity, bridges, missing parts, BGA shadow. | No defects |
| 2 | No battery. Resistance from each rail to ground. | > 1 kΩ on every rail |
| 3 | Bench supply 4.0 V on VBAT, current limit 100 mA. | Idle draw < 30 mA, no part warmer than 5 °C above room |
| 4 | Measure every rail at its test point. Fit jumper J-AUDIO first: AUDIO_EN has a pull-down and no firmware is loaded yet. | 3V3 3.30 ±3 % · 3V0_A 3.00 ±2 % · 1V8_D 1.80 ±3 % |
| 5 | Plug USB to a computer. Flash the test firmware. | Enumerates as USB-serial/JTAG, flash succeeds |
| 6 | I²C scan. | Charger, gauge and DAC respond |
| 7 | Display test pattern, backlight 0–100 %. | No dead lines, backlight smooth |
| 8 | eMMC: read size, write and read back 100 MB. | ≈ 14.6 GiB usable, no errors, ≥ 4 MB/s |
| 9 | Audio: 1 kHz tone into 32 Ω, sweep volume; plug and unplug headphones. | With every gain register at max: ≤ 150 mV RMS open and on 16/32/64/300 Ω; detect works; no pop |
| 10 | Keys and HOLD: press each, check the log. | Each key once per press, HOLD blocks all |
| 11 | Real cell connected. Charge from 3.6 V, log current and NTC temperature. | 400 mA CC, terminates at 4.2 V, zero charge current above 45 °C, also after a watchdog reset |
| 12 | Current per mode: playing screen off, playing screen on, paused, deep sleep, ship mode. | Within section 3.1 targets |
| 13 | Wi-Fi: join the test network, sync 500 MB, unplug mid-sync, plug again. | Sync resumes, hashes match, radio off on battery |
12Verification and test plan
| Test | Method | Units | Pass criteria | Req. |
|---|---|---|---|---|
| Drop | 0.92 m × 4 onto vinyl tile over concrete, random orientation (16 CFR 1500.53) | 3 | Works, glass intact or held by film, no sharp edges (1500.48/49), no loose parts | R-50 |
| ESD | IEC 61000-4-2, ±8 kV contact on USB shell, jack, screws; ±15 kV air on seams, keys, glass | 2 | No damage; recovers without a power cycle | R-51 |
| Splash | IEC 60529 IPX4 oscillating tube, 10 min, powered off | 2 | No water inside, works after 24 h | R-52 |
| Front plate | Pull-off force at the notch; 1,000 remove/fit cycles; use-and-abuse on device and plate, then check no magnet is accessible | 3 | 4–8 N, no loss of hold, no magnet exposed or loose | R-14 |
| USB overvoltage | 9, 12 and 20 V continuous on VBUS; surge per the lab | 2 | No damage; the charger never sees more than its rating | R-32 |
| Key life | Robot press 500k on next key, 200k on others, force logged every 50k | 2 | Force within ±20 %, no missed presses | R-13 |
| Connector life | USB-C 10k and jack 10k insertion cycles, then side-load 20 N | 2 | Works, no lifted pads | R-53 |
| Audio | Analyser: max level with every register at max on 16/32/64/300 Ω and open; noise; THD+N at 100 mV; pop transients | 3 | R-21 to R-23 met | R-21–24 |
| Thermal charging | Charge + sync at 25 °C and 35 °C ambient, thermocouples on cell and case | 2 | Zero charge current above 45 °C cell, including MCU hang, watchdog reset and NTC open/short; case ≤ 43 °C | R-32 |
| Runtime | Full charge, play 128 kbps MP3 at 27 mV until shutdown | 3 | Report the distribution; objective ≥ 16 h | R-31 |
| Sleep current | µA meter in deep sleep and ship mode | 3 | ≤ 100 µA and ≤ 10 µA | R-33 |
| RF | Return loss of the antenna in the closed unit, throughput at 5 m from the router | 2 | S11 ≤ −10 dB across 2.4–2.5 GHz, ≥ 1 MB/s | R-40 |
| Fit | Measure gaps, glass recess, key travel, screw torque | 10 | Per drawings | R-01–03 |
12.1 Desk simulation before EVT
The same tests, run as simple calculations on the design numbers. Rev. 6 is re-checked with the corrected models, then rev. 7. "Needs test" means a fix is designed in but unproven. They do not replace the lab.
13Compliance plan
Launch market: United States first (D-8). The design stays CE-ready so Europe does not force a redesign. The test lab writes the classification matrix (toy or not, age grading, battery rules) before the mould is frozen.
| Market | Standard / rule | Notes |
|---|---|---|
| US | FCC Part 15 B (unintentional) + modular grant of the ESP32-S3 module (intentional) | Build on the module grant only within its conditions (antenna type, gain ≤ 2.33 dBi, labelling). The product still needs its own Part 15 B and RF-exposure assessment. |
| US | CPSIA: lead in substrate ≤ 100 ppm, phthalates ≤ 0.1 % (if treated as a toy), ASTM F963-23, third-party testing, Children's Product Certificate, tracking labels | Children's-product duties apply to the 8–12 part of the audience. F963-23 extends use-and-abuse tests above 96 months only for toys with small-part batteries (Federal Register 2024-00741): the lab decides whether the 603040 pack qualifies. Magnets: F963 magnet requirements for toys under 14 (section 6.5). |
| US | COPPA for the parent app and backend | Amended rule, compliance from 22 April 2026: data inventory, persistent identifiers, retention, deletion, third parties |
| EU / UK | RED (EN 300 328, EN 301 489), EN 62368-1, EN 50332-1/-2, EN 71-1 if classed as a toy, RoHS, REACH, WEEE, battery regulation | Second market. Also RED cybersecurity (EN 18031) since 1 Aug 2025, CRA (reporting from 11 Sep 2026, main obligations from 11 Dec 2027), EU battery removability from 18 Feb 2027, EN IEC 62115 if classed as a toy, UK PSTI |
| Battery | IEC 62133-2, UN38.3, MSDS for shipping | Reports from the cell supplier |
14Open items and risks
| # | Item | Owner | Closes in |
|---|---|---|---|
| O-1 | Cell maximum thickness and end-of-life swelling, in writing (stack allows 1.75 mm free room). | Product + cell supplier | Before phase C |
| O-2 | Attenuator values (start 47 / 7.5 Ω) from a worst-case calculation and measurement; noise and frequency response with the DC-blocking caps. | Builder | Phase B |
| O-3 | NTC network so HOT trips at 45 °C with the cell's real B-curve; chamber test including MCU hang and NTC faults. | Builder | Phase B |
| O-4 | OVP switch MPN and surge/continuous overvoltage test. | Builder | Phase B |
| O-5 | Memory budget on N4R2 (frame buffer, decoder, TLS, 2 OTA + factory in 4 MB). | Builder (firmware) | Phase A |
| O-6 | Display panel MPN: backlight current, FPC exit, active-area offset. | Builder | Phase B layout |
| O-7 | Antenna MPN with gain ≤ 2.33 dBi; tuning and range in the closed shell. | Builder | Phase C |
| O-8 | Ø2.8 boss neck clearance to the display module (0.2 mm nominal) with real tolerances. | Builder (CAD) | Phase C CAD |
| O-9 | Glass vs PC cover: drop and abrasion results. | Product | Phase C |
| O-10 | Runtime: real current with decoder and I²S; decide the promise after a rundown. | Builder | Phase A–B |
| O-11 | US classification matrix from the lab (toy or not, small-part battery, age grading). | Compliance lab | Before mould |
| O-12 | Costed BOM with quotes; the $32–38 figure is an estimate. | Builder | Phase B |
| O-14 | Plate hold force (4–8 N) and magnet grade with real parts; wear after 1,000 swaps. | Builder | Phase C |
| O-15 | Lab confirmation that sealed magnets pass F963 / EN 71-1 after use-and-abuse. | Compliance lab | Before mould |
| O-16 | Supplier swelling figure vs the 0.95 mm free room; if above ≈ 15 %, grow the body to 15.8 mm. | Product + cell supplier | Before phase C |
| O-13 | Renders still show the 106 mm body; update after EVT. | Design | After phase C |
15Revision history
| Rev. | Date | Change |
|---|---|---|
| 4 | 2026-11 | 1.9″ display, 96 mm body, Wi-Fi only, wired audio only, no speaker, separate volume keys, HOLD switch. |
| 5 | 2026-11 | Screws moved to the back and made symmetric, strap slot removed, collisions fixed (screws/display, jack/board, antenna, battery/USB-C). |
| 6 | 2026-11-21 | ESD protection, IPX4 sealing, ≥ 500k switches, Ø4 bosses with thread-forming screws, 1.35 mm floor, hardware volume cap, audio LDO, NTC + JEITA, ship mode, 15 mm antenna, anti-splinter film. This document created. |
| 7 | 2026-11-21 | Applies audit decisions D-1 to D-8: 15 mm body and battery stack; ESP32-S3-MINI-1U-N4R2 at real size with a W.FL antenna lead; DAC at real size with DC-blocking caps and a series/shunt attenuator; 45 °C charge trip in hardware; low-voltage TVS + ≥ 28 V OVP; home key off TS/MR; glass and PC covers on a 1 mm ledge; board U-slots; US-first compliance. Front face grid (2.9 / 1.3 mm). R-21, R-23, R-31, R-32, R-33 rewritten with conditions. Test lab separates calculated results from tests still needed. |
| 7.1 | 2026-11-21 | Swappable magnetic front plate (section 6.5): 0.8 mm plate in a 0.8 mm recess, left hook, 4 magnets sealed in the front shell, steel discs in the plate. Internal stack moved back 0.8 mm; swelling room 1.75 → 0.95 mm. R-14 and the front-plate test added. |